INSTALLATION GUIDELINES


• Master Controller (Smart Network Controller)

Follows below step for Connecting Master controller to Home Network.

Step 1: Associating the Master Controller with Customer Id
Unpack the Master Controller box and look for MAC ID written on the back side of the Master Controller as shown below.
Now send SMS of this MAC ID to installation support backend team (Phone No. XYZ). Or Call up installation support team for registering this master controller. The installation support team will associate this master controller with intended Customer ID.
Step 2: Registering the Master Controller
Connect the Master Controller’s WAN port to a free port on your home router or home network device with Ethernet cable as shown below & Keep the Master Controller in the switched Off position.
Step 3: Login & register
Use a PC, which is connected to internet & access http://myhomeqi.com through a web browser and enter customer ID, user name and password which were created during the Step 1/which are available in the installation work order. Once you have successfully logged into the customer account, the gateway MAC ID will be listed in the account main page & the status will be shown as not-registered with RED mark. Now switch ON the gateway and leave it on for more than 5 Minutes till the gateway MAC on the main page becomes GREEN. During this process the gateway will reboot multiple times. Please do not disconnect or Power off the gateway any of these can render the Master Controller useless.

• Dual Switch ( Two Lighting ON/OFF Circuit Module )

Above symbol stands for

N = Power Neutral

L, IN=Phase /Live Power

O1, O2 = Lights Loads

S1, S2=Switch Connection

Steps for mount inside gang box

1. Open Gang box and find all above required wire’s for Installing module inside gang box, use Multi-Meter for finding Neutral wire.

2. The electricity to the circuit must be shut off during installation for safety and to ensure that wires are not short-circuited during installation.

3. Follow colour coding for connecting dual switch module to Ac power supply.

4. Check device specification before connecting loads to the module.

5. Check all wire connection should be proper tight before closing Gang box

Adding the dual switch to Home Automation Network

1. Log in through webpage www.myhomeqi.com using login, password for mobile app

2. Press the button labelled "Add device "

3. While the switch is powered on , Either press the Program icon against the device on webpage 3 times within 1.5 secs, or Press the external switch/ Button S1 control 3 times in 1.5 sec succession


• Light Dimming Module

Above Symbol stands for
N= Power Neutral
L=Phase /Live Power
O = Lights Loads
S1, COM=Switch Connection

Steps for mount inside gang box

1. Open Gang box and find all above required wire’s for Installing module inside gang box, use Multi-Meter for finding Neutral wire.

2. The electricity to the circuit must be shut off during installation for safety and to ensure that wires are not short-circuited during installation.

3. Follow colour coding for connecting dual switch module to Ac power supply.

4. Check device specification before connecting loads to the module.

5. Check all wire connection should be proper tight before closing Gang box

Adding the Light Dimmer to Home Automation Network

1. Log in through webpage www.myhomeqi.com using login, password for mobile app

2. Press the button labelled "Add device "

3. While the switch is powered on , Either press the Program icon against the device on webpage 3 times within 1.5 secs, or Press the external switch/ Button S1 control 3 times in 1.5 sec succession


• Appliances Energy and ON /OFF Controller -16 AMP Switch

Above Symbol stands for
N= Neutral Power
L =Phase /Live Power

Warning

The incandescent light plugged into the Z-Wave controlled outlet on this module must not exceed 3520 watts resistive load and 1500 W 6.52A incandescent load.

Step For Plugging

6. Check Power polarity use electrical tester before plugging module.
7. Check device specification before connecting loads to the module

Adding the dual switch to Home Automation Network

4. Log in through webpage www.myhomeqi.com using login, password for mobile app
5. Press the button labelled "Add device "
6. While the switch is powered on , Either press the Program icon against the device on webpage 1 times within 1.5 secs or Press the external switch/ Button S1 control 3 times in 1.5 sec succession.

• Fan Controller

Above Symbol stands for
N= Power Neutral
L=Phase /Live Power
O = Lights Loads
S1, COM=Switch Connection

Steps for mount inside gang box

1. Open Gang box and find all above required wire’s for Installing module inside gang box ,use Multi-Meter for finding Neutral wire .

2. The electricity to the circuit must be shut off during installation for safety and to ensure that wires are not short-circuited during installation .

3. Follow colour coding for connecting dual switch module to Ac power supply.

4. Check device specification before connecting loads to the module .

5. Check all wire connection should be proper tight before closing Gang box

Adding the Fan Controller to Home Automation Network

1. Log in through webpage www.myhomeqi.com using login, password for mobile app
2. Press the button labelled "Add device "
3. While the switch is powered on , Either press the Program icon against the device on webpage 3 times within 1.5 secs, or press the external switch/Button S1 control 3 times in 1.5 sec succession .

• AC Temperature Controller

Before using power up the AC Extender using the supplied AC/DC adaptor or USB Power or Dry battery AAA x 3pcs;

Adding the AC Temperature Controller to Home Automation Network

1. Log in through webpage www.myhomeqi.com using login, password for mobile app

2. Press the button labelled "Add device "

3. While the switch is powered on , Either press the Program icon against the device on webpage 1 times within 1.5 secs or Press the external switch/ Button S1 control 3 times in 1.5 sec succession.